Updated on July 7, more Rob is a licensed pool service industry professional with over 20 years of experience. Judging from the questions pool owners ask on the internet, they are having a hard time with water clarity even when they think all the chemicals are balanced. We will discuss in this article why chlorine, pH, and alkalinity are only the beginning in maintaining clear pool water, and then we will troubleshoot the problem. Basic Chemical Requirements for Clear Pool Water Just to summarize, these are the basic chemical requirements for a pool that stays clear. But there is a little more to it than the basics, as you can see in Question 2 below. Unless the water has a sufficient level of free chlorine, algae will grow and make your pool green and cloudy. Shocking a pool with too high pH will cause cloudiness. The right range of alkalinity dissolved salts that keep pH stable makes pH and chlorine levels easier to maintain. Read each of the five questions below:

Why There’s Sand in Your Pool and How to Get it Out

Intex Pool Filter Pump Upgrades: Intex pools are very well known to be a quality pool for the price; a nice starter pool. Intex Fast Set and Frame Set pools are also known for coming with filters that are a bit on the small side, to make the package price competitive.

The dirt is removed by the sand and the clean water flows through the piping (laterals) at the bottom of the filter, up through the standpipe, back to the valve on top of the filter, where the clean water is returned to the pool through the piping or hoses.

Eco Kleer 19″ Pool 1 H. Their Sand Filter Eco Kleer System is preferred by users who value low maintenance and high accountability. The Sand Filter comes in several different sizes to meet the needs of your above ground pool. The process is efficient: Water is pulled through the sand strategically. The sand removes all sediment, dirt and unwanted materials from the pool water.

The pool water is released back into the pool: To maintain the system, simply backwash the Eco Kleer as needed.

Comment navigation

Potential of abundant, environmentally harmless energy technology , which already exists My strategy for manifesting that energy event for humanity’s and the planet’s benefit. I w as born in In that same year, I had my cultural and mystical awakenings. During my second year of college, I had my first existential crisis and a paranormal event changed my studies from science to business. I s till held my energy dreams, however, and in , eight years after that first paranormal event, I had a second one that suddenly caused me to move up the coast from Los Angeles to Seattle, where I landed in the middle of what is arguably the greatest attempt yet made to bring alternative energy to the American marketplace.

In order to properly hook up your above ground pool filter system you will first need to make sure you have everything to do so. You will need the pump, the filter which may be sand, D.E. or a cartridge, pool hoses to connect the pump, filter all to the pool or rigid PVC plumbing that will connect the pump and filter to the pool.

My main question is that my acrylic steps are getting small cracks in it. Is there a way to coat them. I think they are causing my leak. The gel- coat on fiberglass or acrylic steps can ‘craze’, but this isn’t the cause of your water loss. Check with your local boat store for fiberglass paints and gel- repair kits, the small cracks in the gel- coat allows pool water to breakdown the fiberglass resin.

Air Bubbles and Solar Heaters Q. I’m getting air bubbles in the pool. It started when the solar heater was installed. The solar man says air can’t get into the solar because it’s on the pressure side of the pump. There were no air problems until then. Your pump is probably undersized for a solar system. If original and typical, it was the smallest pump capable of filtering your pool as it was contracted and built.

Solar systems require at least one step- up in pump size to push water to your roof. The increase in pressure causes an equal increase in vacuum.

1/2 HP Sand Filter & Pump Kit, AL50

Click here to return to Metro Pool Service home. The office staff is always so nice and helpful and they have been more than happy to help whenever I have needed them. Will never use anyone else. Green Tulsa, OK “Your kindness and professionalism has been exceptional.

I have an older used sand filter, and a new pump hooked up to my above ground pool. We are just setting this up and cannot get it to backwash. We replaced the sand thinking that might be the problem.

Winterization also requires you to disconnect the hoses for the pool, pump and filter. Once the winter is over, and the outdoor temperatures begin to rise, it is time to reopen the pool for the summer. Trying to remember where each of the three hoses attach to your filter, pool and pump can quickly spell disaster if you mix up the connections. Correctly hook up your sand filter and pump to your above-ground pool for hours of summer fun.

Make sure to locate it near the skimmer and return on your pool. Ensure the ground is level beneath the pump and filer. Place the pump and filter on concrete blocks for additional stability. Pumps can be hardwired to the breaker, or plug into an outdoor receptacle.

BEST POOL FILTERS REVIEWS 2018 (BUYING GUIDE & COMPARISON CHART)

Would you like to merge this question into it? MERGE already exists as an alternate of this question. Would you like to make it the primary and merge this question into it? MERGE exists and is an alternate of.

Pond Filter, Car Washing Filter, Garden Filter, Pool Filter — Works anywhere you use a garden hose. If you need an outdoor water filter to make chlorine-free water for your petunia bed or your dog’s water bowl, to reduce the hardness in the water you use to wash your car or rinse your patio, or to remove the chemicals and chlorine from the.

Think of this in three parts; I first build it, then I break it, then I fix it. It does a fantastic job of filtering out particles but does need to be backwashed or flushed on a somewhat regular basis. Performing a backwash required multiple tools and multiple steps. To combat this, we installed a screw-on pipe fitting: That also does mean that the wrench is needed to loosen it, too. Specifically, a wide-mouth pipe wrench is needed: Note how chewed up the cap is from being tightened and loosened so many times.

The next step is to fetch our hose from storage and unfurl it…. Properly drying out the hose; curling it up; and then putting it away is far too time consuming to be worth doing. As a result, we just keep the hose out in the open in between backwash sessions. We slide the hose onto the end of the pipe: This picture should also show the next piece, but I lost it just before undergoing this project.

You can see the tiny holes forming in the hose from the clamp. We need to trim off a couple of inches every so often when they get too bad.

How to Remove Fine Dust, Sand or Sediment From a Pool

Sand lasts around 5 years No need to constantly clean or replace filter cartridges Sand pumps tend to last longer than cartridge filter pumps How To Install The Intex GPM Send Filter Pump The Intex 2, gallon sand filter pump is easy to install as it is designed to hook right up to the existing hose connectors on your Intex pool, no need to buy adapters to make it fit. You will need at least pounds of sand; it needs to be 20 grade silica sand which should be readily available from local outlets.

Also follow the procedure in the owners manual for back washing, this will make sure that any fine sand particles or other impurities are removed before you put the filter into service cleaning your pool. It gives you a lot of control. The water is sucked from the pool, passes through the control valve into the filter tank, and soaks down through the sand leaving any undesirable particles behind.

After being cleaned the water passes through the outlet of the control valve and is returned to your pool.

Hooking up the hoses to a pool filter pump for an above ground pool is a job that should be undertaken by a qualified electrician, or at the very least he checks and signs off the job as safely and correctly completed as required by law.

This should include the cover, the air pillow, the plugs for the skimmers gizzmos or rubber plugs , the winter plate if used and your winterizing chemicals. You need these items for proper winterization. If you are using the green Gizzmos to plug your skimmers, check them out and make sure that they are not cracked. This is very important when dealing with gizzmos. Gizzmos with holes or cracks will not work!

Backwash the filter very well to clean it out. Drain DE filter tanks and leave backwash valve open. On sand filters, unplug the filter drain plug and leave off. Put drain plug with other removed items in the pump basket. Make sure multiport valve if any has no water in it. Blow it out with a compressor or shop vac if necessary. Please note that it is not recommended to “acid wash” DE filters at the time of the pool closing.

This is best to do in the Spring so that you can immediately run pool water through the system.

ASK A BRAND

Diatomaceous Earth DE takes out much smaller particles much more quickly than any other filter. Take a look at a bottle of filter sand and a bottle of diatomaceous earth. The different is apparent. On this, there is no question, end of discussion. DE removes particles down to three microns, all the time.

A swimming pool filter helps maintain clean and healthy pool water. The pump sends water to the filter, which cleans it out before sending it back out into the pool. Public pools follow certain laws stating that a certain amount of water must go through the filter in a certain amount of time.

A swimming pool filter helps maintain clean and healthy pool water. The pump sends water to the filter, which cleans it out before sending it back out into the pool. Public pools follow certain laws stating that a certain amount of water must go through the filter in a certain amount of time. This ensures that the pool remains a safe and sanitary environment.

You can install your own filter in about 10 minutes. Step 1 — Understand Your Filter A pool filter is placed between the inflow and outflow hoses that carry water into and out of the pool. The outflow hose sucks water out of the pool, toward the filter. Normally this hose is placed about halfway down into the side of the pool, where it can suck out water circulating in the bottom or the middle of the pool.

The filter normally looks like the filter of a car, designed to trap debris and smaller matter. The clean water then gets pushed back into the inflow hose and back into your pool toward the top of the pool. Step 2 — Installation Begin by ensuring that the cartridge is securely installed. Recognize which hole is for inflow lower and which is for outflow upper.

When connecting the hose ends, ensure that they are going into the proper connectors before securing them. Normally, these hoses will be protected by hose clamps that you can manually tighten with a screw or a self-tensioned clamp.

Installing an 18″ sand filter with tidal wave 1 horse pump